Do It Yourself Bathtub Installation.
Do It Yourself Bathtub Installation.
Blog Article
Just how do you actually feel in relation to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a tub isn't exactly brain surgery, but it does call for strong plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately difficult job. If the old tub is readily obtainable, the project can relocate rapidly; if you need to open a wall surface to remove the old bathtub and also position the brand-new bathtub, the job is much harder. In either situation, the project is within a residence handyman's abilities, although you will certainly need an assistant to move out the old bathtub and also set in the brand-new one. Make sure you have certified yourself for the task and also are comfortable trying it. Rather than hiring a service provider to take control of a halfway-completed job, it is far better to consider utilizing one prior to you begin. Possibilities are you may require a professional plumber to make tube connections.
This write-up will assist you mount a brand-new bathtub in your shower room if you have actually already purchased a brand-new tub and also do not need to alter the setup of your previous water supply pipes.
Your devices and also material checklist must comprise the following:
Planning for the Installation
First of all, the sustaining structure supplied with the bath must be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets system to avoid pressure on the bathtub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to now be ready to be fitted in its final setting.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the supply of water. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the restricted access that is frequently the case.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a towel prepared for the remaining water that will come from the pipelines. When the supply pipes have actually been eliminated, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any old securing compound.
Prior to carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Using both wood boards under its feet, put the bathtub in the needed position. The wood boards are useful in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the bathtub up until the level reads level.
To mount faucets, fit the bottom of the furthest adaptable faucet connector to the proper supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the supply of water and also examine all joints and also brand-new pipework for leakages and tighten them if needed. Fill the tub and also check the overflow outlet and the regular electrical outlet for leakages.
Finally, repair the bath paneling as described in the producer's instruction manual. Tiling as well as sealing around the tub ought to wait up until the tub has been utilized at the very least once as this will settle it right into its last position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a link to the current supply pipelines.
If you need to fit a monobloc, then you will need reducing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making certain that the washers are in location in between the tap and also the sink. Secure the tap in position with the manufacturer supplied backnut. When the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet adapters. The former type must be attached to the tap ends initially, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break an inflexible seal, triggering the water to pass through the wall in between the bathroom as well as the tiling, bring about complications with moisture and also possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components as well as installations. They are sold in tubes as well as cartridges, and also are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill up the tub with water before securing, to enable the activity experienced when the tub remains in use. The sealant can fracture fairly very early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily offered on the marketplace. It is a good idea to fit the floor tiles using water-resistant or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading up on How to Install a Bathtub Yourself? Create a remark down the page. We will be pleased to know your opinion about this page. We are looking forward that you come back again in the near future. Enjoyed reading our content? Please share it. Let others locate it. Thanks a bunch for your time. Don't hesitate to stop by our blog back soon.
Detail Report this page